Titanium alloy with low carbon content is obtained because the carbon content remains the original concentration. The hardness of titanium alloy is mainly related to its carbon content. Therefore, after carburizing and subsequent heat treatment, the workpiece can obtain the performance of hard and tough inside. Galvanized wire varieties are mainly classified into three categories: electric galvanized wire, hot galvanized wire and galvanized wire. Among them, the classification of galvanized wire is divided into large roll galvanized wire, medium roll galvanized wire, small roll galvanized wire, galvanized shaft wire, truncated galvanized wire and other main production varieties.
In order to pack and bind galvanized wire in the surface of the sedimentary layer to local removal of surface film, surface inclusion and other defects can be found and treated by conventional technology; Excess foam is formed when soap and surfactants such as saponified fats are brought into the tank. Moderate rates of foam formation may be harmless. Small, homogeneous particles of large denier present in the bath can stabilize the foam layer. Use activated carbon mat to remove surface active substance. Or through filtration to make the foam is not too stable, which are effective measures; Other measures should also be taken to reduce the amount of surfactant introduced. The electroplating speed can be obviously reduced by the addition of organic matter. Although chemical formulations facilitate high deposition rates, the deposition of organic matter does not meet the requirements of coating thickness, so activated carbon can be used to treat the bath.
Some large roll galvanized wire products in order to meet different industrial needs, will be further processed on the surface, such as the anti-corrosion layer, galvanized, iron plating, aluminum alloy plating, or in the galvanized wire appearance above the copper plating, brass plating, etc., to strengthen the steel wire and colloidal years and capabilities. Generally, galvanized wire products should be well plated and drawn when they are produced, and the sequence of the two processes should be decided according to the production or industrial needs.
The use of welding network is very wide, but also used in different industries, different places, many times the name is because of the use or use of the name, so the various uses of the welding network, destined to name a variety of different. Can be called row welding net, or zinc plating welding net or galvanized welding net. And then there’s the external insulation wire, just for insulation, usually on the outside of the wall, to reduce heat loss.
Low and medium carbon steel wire is used as raw material, with good surface gloss, uniform zinc layer, strong adhesion, corrosion resistance and so on. Available: diameter 1.60mm-4mm (16#-33#) cold plating wire; Diameter 6.40mm-0.81mm(8#-21#) black iron wire, changed wire. It is mainly used in communication equipment, medical equipment, weaving net, brush, steel cable, filter, high-pressure pipe, construction, crafts and other industries.
Wire-wall welding net is widely used in industrial production, agriculture, engineering construction, transportation, mining and other processing and manufacturing industries. Such as machinery and equipment protective cover, animal guardrail, pot flower guardrail, window fence, safety exit guardrail, poultry cage, egg basket and home office food industry basket, paper basket and design decoration. It is suitable for general engineering building wall, pouring concrete, multi-storey building, etc., which plays an important structural role in the thermal insulation system. In the construction of the building, the thermal insulation board of hot-dip galvanized electric welding grid is placed on the inside of the outer mold of the wall to be concreted. The external thermal insulation board and the wall are one kind of live, and the thermal insulation board and the wall are integrated into one body after the removal of the mold. The coating on the surface of the weld core is called the coating. The coating of electrode plays a very important role in the welding process. If the photoelectrode without drug skin is used for welding, in the welding process, oxygen and nitrogen in the air will invade a large number of molten metal, metal iron and beneficial elements such as carbon, silicon, manganese oxidation and nitriding to form various oxides and nitrides, and residual in the weld, resulting in slag inclusion or cracks in the weld. The gas in the weld pool may produce a large number of pores in the weld. These factors can greatly reduce the mechanical properties of the weld and make it brittle.
