Infrared analysis showed that the characteristics bands for the bare nanoparticles are still exhibited in the vitamins@P25TiO2NPs spectra, such as a wide peak in 450–1028 cm−1 related to the stretching vibration of Ti-O-Ti and other peaks in 1630 cm−1 and 3400 cm−1, which represent the surface OH groups stretching. The IR spectrum of vitaminB2@P25TiO2NPs showed signs of binding between compounds. The OH bending peak (1634 cm−1) corresponding to bare nanoparticles disappeared, and the NH2 bending band characteristic of vitamin B2 appeared (1650 cm−1). The IR spectrum of vitaminC@P25TiO2NPs also showed signs of successful functionalization. Bands at 1075 cm−1; 1120 cm−1; 1141 cm−1 were observed, which are originated by C
O-C vibrations present in the vitamin C. The intense band at 1672 cm−1 is attributed to the C = O stretching in the lactone ring while the peak at 1026 cm−1 is ascribed to the stretching vibration Ti-O-C. Wide bands at 3880–3600 cm−1 are related to stretching vibration OH groups, but those disappear in the modified nanoparticles spectrum. These observations confirm the interactions between the P25TiO2NPs and the vitamins [35].
A great number of other brands with fancy names have gone out of the German market, because of some defects in the processes of manufacture. The English exporters, as a rule, offer three or four grades of lithopone, the lowest priced consisting of about 12 per cent zinc sulphide, the best varying between 30 and 32 per cent zinc sulphide. A white pigment of this composition containing more than 32 per cent zinc sulphide does not work well in oil as a paint, although in the oilcloth and shade cloth industries an article containing as high as 45 per cent zinc sulphide has been used apparently with success. Carefully prepared lithopone, containing 30 to 32 per cent sulphide of zinc with not over 1.5 per cent zinc oxide, the balance being barium sulphate, is a white powder almost equal to the best grades of French process zinc oxide in whiteness and holds a medium position in specific gravity between white lead and zinc oxide. Its oil absorption is also fairly well in the middle between the two white pigments mentioned, lead carbonate requiring 9 per cent of oil, zinc oxide on an average 17 per cent and lithopone 13 per cent to form a stiff paste. There is one advantage in the manipulation of lithopone in oil over both white lead and zinc oxide, it is more readily mis-cible than either of these, for some purposes requiring no mill grinding at all, simply thorough mixing with the oil. However, when lithopone has not been furnaced up to the required time, it will require a much greater percentage of oil for grinding and more thinners for spreading than the normal pigment. Pigment of that character is not well adapted for use in the manufacture of paints, as it lacks in body and color resisting properties and does not work well under the brush. In those industries, where the paint can be applied with machinery, as in shade cloth making, etc., it appears to be preferred, because of these very defects. As this sort of lithopone, ground in linseed oil in paste form, is thinned for application to the cloth with benzine only, and on account of its greater tendency to thicken, requires more of this comparatively cheap thinning medium, it is preferred by most of the manufacturers of machine painted shade cloth. Another point considered by them is that it does not require as much coloring matter to tint the white paste to the required standard depth as would be the case if the lithopone were of the standard required for the making of paint or enamels. On the other hand, the lithopone preferred by the shade cloth trade would prove a failure in the manufacture of oil paints and much more so, when used as a pigment in the so-called enamel or varnish paints. Every paint manufacturer knows, or should know, that a pigment containing hygroscopic moisture does not work well with oil and driers in a paint and that with varnish especially it is very susceptible to livering on standing and to becoming puffed to such an extent as to make it unworkable under the brush. While the process of making lithopone is not very difficult or complicated, the success of obtaining a first class product depends to a great extent on the purity of the material used. Foreign substances in these are readily eliminated by careful manipulation, which, however, requires thorough knowledge and great care, as otherwise the result will be a failure, rendering a product of bad color and lack of covering power.