Overall, buff percentage is a critical factor that manufacturers of titanium dioxide must carefully manage to ensure the quality, consistency, and cost-effectiveness of their products. By investing in advanced technology and processes to control buff percentage, manufacturers can meet the specific requirements of their customers and maintain a competitive edge in the market. As the demand for titanium dioxide continues to grow across various industries, manufacturers must continue to innovate and improve their processes to meet the evolving needs of their customers.
tion of the precipitate, the mass is filter pressed, dried, muflled and processed in the on the market, in that the {covering capacity of the pigment is greatly increased, as well The titanium oxide is peptized or held in as its fastness to light, and ease of working in oils. It is also superior to the so called double strength lithopone made by doubling the zinc sulphide conent, in that it is very neutral to acid vehicles. It is also far superior to other titanium compounds on the market, inasmuch as greater opacities are obtained with a relatively small amount of titanium oxide, than has heretofore been obtained with far greater proportions of titanium oxide, thereby effecting a considerable economy over that of other similar products containing'titanium oxide.
Titanium dioxide is an inert earth mineral used as a thickening, opacifying, and sunscreen ingredient in cosmetics. It protects skin from UVA and UVB radiation and is considered non-risky in terms of of skin sensitivity. Because it is gentle, titanium dioxide is a great sunscreen active for sensitive, redness-prone skin. It’s great for use around the eyes, as it is highly unlikely to cause stinging.
Different dermal cell types have been reported to differ in their sensitivity to nano-sized TiO2 . Kiss et al. exposed human keratinocytes (HaCaT), human dermal fibroblast cells, sebaceous gland cells (SZ95) and primary human melanocytes to 9 nm-sized TiO2 particles at concentrations from 0.15 to 15 μg/cm2 for up to 4 days. The particles were detected in the cytoplasm and perinuclear region in fibroblasts and melanocytes, but not in kerati-nocytes or sebaceous cells. The uptake was associated with an increase in the intracellular Ca2+ concentration. A dose- and time-dependent decrease in cell proliferation was evident in all cell types, whereas in fibroblasts an increase in cell death via apoptosis has also been observed. Anatase TiO2 in 20–100 nm-sized form has been shown to be cytotoxic in mouse L929 fibroblasts. The decrease in cell viability was associated with an increase in the production of ROS and the depletion of glutathione. The particles were internalized and detected within lysosomes. In human keratinocytes exposed for 24 h to non-illuminated, 7 nm-sized anatase TiO2, a cluster analysis of the gene expression revealed that genes involved in the “inflammatory response” and “cell adhesion”, but not those involved in “oxidative stress” and “apoptosis”, were up-regulated. The results suggest that non-illuminated TiO2 particles have no significant impact on ROS-associated oxidative damage, but affect the cell-matrix adhesion in keratinocytes in extracellular matrix remodelling. In human keratinocytes, Kocbek et al. investigated the adverse effects of 25 nm-sized anatase TiO2 (5 and 10 μg/ml) after 3 months of exposure and found no changes in the cell growth and morphology, mitochondrial function and cell cycle distribution. The only change was a larger number of nanotubular intracellular connections in TiO2-exposed cells compared to non-exposed cells. Although the authors proposed that this change may indicate a cellular transformation, the significance of this finding is not clear. On the other hand, Dunford et al. studied the genotoxicity of UV-irradiated TiO2 extracted from sunscreen lotions, and reported severe damage to plasmid and nuclear DNA in human fibroblasts. Manitol (antioxidant) prevented DNA damage, implying that the genotoxicity was mediated by ROS.
The major applications studied in the report include paints & coatings, plastics, printing inks, paper & pulps, rubber, leather, linoleum, and others. Region-wise, the market is studied across North America, Europe, Asia-Pacific, and LAMEA. Presently, Asia-Pacific accounts for the largest share of the market, followed by North America and Europe.
